Pepperl Fuchs UC400-F77-EP-IO-V31 – Ultrasonic sensor. Single head system

Ultrasonic sensor. Single head system, IO-Link interface for service and process data, Programmable via DTM with PACTWARE, Continuous distance value via IO-Link process data, Series: -F77, Operating voltage: 10 ... 30 V DC , ripple 10 % SS , Interface type: IO-Link (via C/Q = Pin 4), Output type: 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected, UL approval: cULus Listed, Class 2 Power Source, CCC approval: CCC approval / marking not required for products rated ≤36 V. Sensing range: 30 ... 400 mm. Adjustment range: 40 ... 400 mm. Dead band: 0 ... 30 mm. Standard target plate: 20 mm x 20 mm. Transducer frequency: approx. 310 kHz. Response delay: minimum : 10 ms factory setting: 37 ms. Sensor cycle time: ≥ 10 ms (factory setting) ; programmable to 60 s. Non-volatile memory: EEPROM. Write cycles: 300000. LED green: solid: power onflashing: standby mode or IO-Link communication. LED yellow: solid: object in evaluation rangeflashing: switch point programming, object detected. LED red: solid: errorflashing: switch point programming, object not detected. Operating voltage: 10 ... 30 V DC , ripple 10 %SS. No-load supply current: ≤ 40 mA. Power consumption: ≤ 400 mW. Time delay before availability: ≤ 300 ms. Interface type: IO-Link (via C/Q = Pin 4). IO-Link revision: 1.1. Device profile: Smart Sensor. Device ID: 0x300301 (3146497). Transfer rate: COM2 (38.4 kBit/s). Min. cycle time: 2.3 ms. Process data width: 16 bit. SIO mode support: yes. Compatible master port type: A. Input/output type: 1 synchronization connection, bidirectional. 0 Level0 ... 1 V1 Level2.5 V ... UBInput impedance> 22 kΩOutput currentcurrent source 22 kΩ. Output current: current source < 2.5 mA. Pulse length: ≥ 1 ms with external control, low active. Synchronization frequency: . Common mode operation≤ 109 HzMultiplex operation≤ 109 Hz / n , n = number of sensors , n ≤ 10: . Common mode operation: ≤ 109 Hz. Multiplex operation: ≤ 109 Hz / n , n = number of sensors , n ≤ 10. Output type: 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected. Rated operating current: 100 mA , short-circuit/overload protected. Voltage drop: ≤ 2.5 V. Repeat accuracy: ≤ ± 0.1 % of full-scale value. Switching frequency: factory setting: 16 Hz programmable max. 35 Hz. Range hysteresis: 1 % of the adjusted operating range (default settings), programmable , min. 1 mm. Temperature influence: ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation). Standard conformity: . StandardsEN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9:2013: . Standards: EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 IEC 61131-9:2013. UL approval: cULus Listed, Class 2 Power Source. CCC approval: CCC approval / marking not required for products rated ≤36 V. Ambient temperature: -25 ... 70 °C (-13 ... 158 °F). Storage temperature: -40 ... 85 °C (-40 ... 185 °F). Connection type: Connector plug M8 x 1 , 4-pin. Degree of protection: IP67. Material: . HousingPolycarbonateTransducerepoxy resin/hollow glass sphere mixture; polyurethane foam: . Housing: Polycarbonate. Transducer: epoxy resin/hollow glass sphere mixture; polyurethane foam. Installation position: any position. Mass: 9 g. Tightening torque, fastening screws: max. 0.2 Nm. Dimensions: . Height31 mmWidth12 mmLength23 mm: . Height: 31 mm. Width: 12 mm. Length: 23 mm. Output: near switch point: 40 mm far switch point: 400 mm Output mode: Window mode Output logic: normally open. Beam width: wide

Specifications