Pepperl Fuchs NRB20-U1-E2-IO

Inductive sensor. Reduction factor 1, magnetic field resistant, Switching function: Normally open/closed (NO/NC) programmable, Output type: PNP, Rated operating distance: 20 mm (factory setting), Installation: flush, Output polarity: DC, Output type: 3-wire, Construction type: <i>VariKont</i> ^®, Series: <i>VariKont</i> ^®, Operating voltage: 10 ... 30 V DC, Switching frequency: 0 ... 440 Hz (switch point mode) <BR>0 ... 10 Hz (window mode, switch point mode with stability alarm). Switching function: Normally open/closed (NO/NC) programmable. Output type: PNP. Rated operating distance: 20 mm (factory setting). Near operating distance: 15 mm (can be activated by software). Installation: flush. Output polarity: DC. Assured operating distance: 0 ... 16.2 mm. Reduction factor rAl: 1. Reduction factor rCu: 1. Reduction factor r304: 1. Reduction factor rSt37: 1. Output type: 3-wire. Operating voltage: 10 ... 30 V DC. Switching frequency: 0 ... 440 Hz (switch point mode) 0 ... 10 Hz (window mode, switch point mode with stability alarm). Hysteresis: typ. 3 %. Reverse polarity protection: reverse polarity protected. Short-circuit protection: pulsing. Voltage drop: ≤ 0.5 V. Operating current: 0 ... 200 mA. Off-state current: 0 ... 0.5 mA typ. 60 µA at 25 °C. No-load supply current: ≤ 20 mA. Time delay before availability: max. 150 ms. Constant magnetic field: 200 mT. Alternating magnetic field: 200 mT. Operating voltage indicator: LED, green. Status indicator: LED, yellow. MTTFd: 701 a. Mission Time (TM): 20 a. Diagnostic Coverage (DC): 0 %. Interface type: IO-Link ( via C/Q = terminal 4 ). IO-Link revision: 1.1. Device ID: 0x201005 (2101253). Transfer rate: COM2 (38.4 kBit/s). Min. cycle time: 2.3 ms. Process data width: Process data input (control system side): 2 Bit Process data output (control system side): none. SIO mode support: yes. Compatible master port type: A. Standard conformity: . StandardsEN IEC 60947-5-2: . Standards: EN IEC 60947-5-2. Protection class: II. Rated insulation voltageUi60 VRated impulse withstand voltageUimp800 V: Ui. Rated insulation voltage: 60 V. Rated impulse withstand voltage: 800 V. UL approval: cULus Listed Load Type: General Purpose Circuitry: Class 2 Power Source Enclosure Type Rating: Type 1 Supply/Switching Voltage: 30 V DC Output Switching Current: 200 mA. CCC approval: CCC approval / marking not required for products rated ≤36 V. Ambient temperature: -25 ... 70 °C (-13 ... 158 °F). Storage temperature: -40 ... 85 °C (-40 ... 185 °F). Connection type: screw terminals. Information for connection: A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 %. Core cross section: up to 2.5 mm2. Minimum core cross-sectionwithout wire end ferrules 0.5 mm2 , with connector sleeves 0.34 mm2Maximum core cross-sectionwithout wire end ferrules 2.5 mm2 , with connector sleeves 1.5 mm2: . Minimum core cross-section: without wire end ferrules 0.5 mm2 , with connector sleeves 0.34 mm2. Maximum core cross-section: without wire end ferrules 2.5 mm2 , with connector sleeves 1.5 mm2. Housing material: PA/metal with epoxy powder coating. Sensing face: PA. Housing base: plastic. Degree of protection: IP67. Mass: 275 g. Dimensions: . Height40 mmWidth40 mmLength118 mm: . Height: 40 mm. Width: 40 mm. Length: 118 mm. Note: Tightening torque: 1.8 Nm (housing). Default setting: operating mode = switch point mode with stability alarm switching function = Normally open (NO) switching distance = 20 mm

Specifications