Pepperl Fuchs OMR60M-R200-2EP-IO-0,3M-V1-L – Distance sensor. Universal distance sensor

Distance sensor. Universal distance sensor, measurement to reflector, IO-Link interface, measuring method PRT, measuring range up to 60 m, red laser light, laser class 1, push-pull output, fixed cable with M12 plug, Medium design with versatile mounting options, Space-saving distance sensors in small standardized design, Measuring method PRT (Pulse Ranging Technology), IO-Link interface for service and process data, Red laser light, laser class 1. Measuring range: 0.2 ... 60 m. Reference target: OFR-500/500. Light source: laser diode. Light type: modulated visible red light. Laser nominal ratings: . NoteLASER LIGHT , DO NOT STARE INTO BEAMLaser class1Wave length660 nmBeam divergence2 mradPulse length4 nsRepetition rate300 kHzmax. pulse energy 300 a. Mission Time (TM): 20 a. Diagnostic Coverage (DC): 0 %. Operation indicator: LED green:constantly on - power onflashing (4Hz) - short circuitflashing with short break (1 Hz) - IO-Link mode. Function indicator: LED yellow:constantly on - switch output activeconstantly off - switch output inactive. Teach-in indicator: Teach-In : LED yellow/green; equiphase flashing; 2,5 Hz Teach Error:LED green/yellow non equiphase flashing; 8.0 Hz. Control elements: Teach-In key. Control elements: 5-step rotary switch for operating modes selection. Operating voltage: 10 ... 30 V DC 18 ... 30 V from IO-Link. Ripple: 10 % within the supply tolerance. No-load supply current: < 25 mA at 24 V Operating voltage. Protection class: III. Time delay before availability: < 900 ms. Interface type: IO-Link ( via C/Q = pin 4 ). IO-Link revision: 1.1. Device profile: Identification and Diagnosis - I&D Smart Sensor - SSP 4.2.1. Process data: Input 6 Byte - measurement value 4 Byte- scaling factor 8 Bit- signal quality 2 Bit- switching signal 1 1 Bit- switching signal 2 1 Bit- diagnosis signals n Bit- additional signals n Bit Output 2 Bit - sensor control function 1 Bit- evaluation control function 1 Bit. Vendor ID: 1 (0x0001). Device ID: 1121041 (0x111B11). Transfer rate: COM2 (38.4 kBit/s). Min. cycle time: 4 ms. SIO mode support: yes. Switching type: The default setting is: C/Q - Pin4: push-pull output, IO-Link Q2 - Pin2: push-pull output. Signal output: 2x push-pull outputs, reverse polarity protected, surge-proof. Switching voltage: max. 30 V DC. Switching current: max. 100 mA , resistive load. Usage category: DC-12 and DC-13. Voltage drop: ≤ 1.5 V DC. Communication interface: IEC 61131-9 / IO-Link V1.1.3. Laser safety: EN 60825-1:2014. Warm up time: 5 min. Measured value output: 1 ms. Average data age: 3 ms (default), 6 ms , 12 ms , 25 ms , 50 ms , 100 ms , adjustable. Absolute accuracy: typ. ± 20 mm (including influence of temperature). Repeat accuracy: < 6 mm. UL approval: E87056 , cULus Listed , class 2 power supply , type rating 1. CCC approval: CCC approval / marking not required for products rated ≤36 V. FDA approval: IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice 56, dated May 8, 2019.. Ambient temperature: -30 ... 60 °C (-22 ... 140 °F). Storage temperature: -40 ... 70 °C (-40 ... 158 °F). Degree of protection: IP67 / IP69 / IP69K. Connection: 300 mm fixed cable with M12 x 1, 4-pin connector. Material: . HousingPC (Polycarbonate)Optical facePMMA: . Housing: PC (Polycarbonate). Optical face: PMMA. Mass: approx. 37 g. Dimensions: . Height50.6 mmWidth15 mmDepth41.7 mm: . Height: 50.6 mm. Width: 15 mm. Depth: 41.7 mm. Switching output 1: Q1: switching signal high-active , Window mode 6000 ... 9000 mm. Switching output 2: Q2: switching signal high-active , Window mode 4000 ... 8000 mm

Specifications